Troubleshooting · KN7000, KN6000, KN5000, KN3000, KN2000Settings that look like faults

Settings that make the keyboard seem broken, grouped by what you notice, with where to change each one.

Written for: KN7000, KN6000, KN5000, KN3000, KN2000.Also called: looks broken, seems faulty, not a fault, MONITOR OFF, MUTE, FADE IN flashing, LOCAL CONTROL, band quiet, only drums, semitone flat, pitch sinking, out of tune, GLIDE, KEY SHIFT, rhythm won't start, wrong tempo, volumes jump, G7, C on G, ON BASS, TECHNI-CHORD, transpose won't stay, no confirmation, MIDI files not shown, silent while loading, floppy light always on, warm case, no MIDI, Attention, program change.

Many faults that owners took to the forums turned out to be a setting. Source: Community report, 2004–2026 The items below are grouped by what you notice. Menu names are the KN7000’s unless an item names another model.

Most settings are reached through PROGRAM MENUS, the button that opens the setting menus, or through CUSTOMIZE. Source: Manual, pp. 30, 181 A part is one of the voices the keyboard plays at once: Right 1, Right 2 and Left for the hands, and the drums, bass and accompaniment of the style. Source: Manual, pp. 29, 190 A style is the keyboard’s backing band, which the manual calls a rhythm. Source: Manual, p. 49

By the manual, switching off and on puts two of these settings back: the speakers come back on, and CLOCK returns to INTERNAL. Source: Manual, pp. 160, 191

Sound

No sound from the speakers or headphones, and MONITOR OFF on the screen

MONITOR SETTING is off. It silences the speakers and the headphones together, and the screen shows MONITOR OFF at the top. Press PROGRAM MENUS, choose SOUND, then MONITOR SETTING, and press ON. It also comes back on each time the keyboard is switched on. Source: Manual, p. 160

Nothing plays, and the FADE IN light flashes

FADE IN is waiting for you. While its light flashes, every part is at volume 0 until you play or press START/STOP. Press FADE IN again to turn it off. Source: Manual, p. 58

A part shows MUTE

Both of that part’s balance buttons were pressed together, which mutes it. The balance buttons are the pairs under the part faders on the home page, the screen shown during normal playing. Press either button of the muted part to bring it back. Source: Manual, p. 29

One part is silent from the keys, but plays from a song

LOCAL CONTROL is off for that part. MIDI is the standard way keyboards and computers send notes to each other. With LOCAL CONTROL off, the part sends its notes as MIDI but makes no sound itself. Source: Manual, p. 190

It’s set in two places: per part on the MIDI menu’s PART SETTING page, and per track for sequencer playback with LOCAL CONT. on the TRACK ASSIGN page. The sequencer is the keyboard’s built-in recorder. Source: Manual, pp. 80, 95, 190

To set it on in the MIDI menu, press PROGRAM MENUS, choose MIDI, then PART SETTING. Choose the part, and set LOCAL to ON. Source: Manual, p. 190 A downloaded style for the KN2000 once left Right 1 set this way. Source: Community report, 2007

The band is quiet

Push up APC/SEQUENCER VOLUME, the slider beside MAIN VOLUME. It sets the volume of the style’s band and of sequencer playback. Source: Manual, pp. 10, 56 One owner’s band dropped to half volume after loading a style, until this slider went back to the top. Source: Community report, 2016

Every key plays a drum sound

DRUM KITS in the SOUND GROUP section is on. Choose another sound group. Source: Manual, p. 201

The reverb is heavy when the keyboard is switched on

Reverb adds the sound of a room. Its overall amount is TOTAL DEPTH: hold REVERB for a few seconds to reach it. Source: Manual, p. 44 One KN7000 owner found the reverb too heavy at switch-on, and the answer given was to turn TOTAL DEPTH down. Source: Community report, 2015

The microphone is only usable at the bottom of MIC VOLUME

In one KN7000 report, the answer given was that the microphone’s output was too strong, and to connect it through a mixer. Source: Community report, 2012

A choir sound from an expansion board growls

An expansion board is an optional board fitted inside the keyboard to add sounds. Source: Manual, pp. 34–35 On one KN7000, a board’s choir sounds growled a second after each note. The cause was the sound’s filter setting in the sound editor, and changing the filter mode cured it. Source: Community report, 2009

Some expansion-board vocal sounds stop above E in the fourth octave

That’s by design: these vocal-pattern sounds have a short range. Source: Community report, 2008

Only GM sounds after loading a MIDI file (KN2000 to KN5000)

GM is the standard sound set that most MIDI files are written for. On these older models, loading a MIDI file can switch the keyboard to GM mode, which leaves only the GM sounds and drum kits. Switch GM off in the disk’s file list. Source: Community report, 2005–2014

A KN6000 sound turns quiet or dull

On the KN6000, the sound-controller wheel and the trackball both change the sound. An unused wheel can drift and dull a sound after about 20 bars. A trackball left off-centre can make a sound quiet and distorted. Move the control back and forth. Source: 2 community reports, 2006

Pitch

The pitch is a semitone low, or sinks while you play

A footswitch is a pedal that plugs into FOOT SW 1 or FOOT SW 2 on the back and can be given a job. One job, GLIDE, bends the pitch down by about a semitone while the switch is pressed. FOOT SWITCH 2 is set to GLIDE from the factory. Source: Manual, pp. 179, 180, 199

A dirty or faulty footswitch socket can act as if the switch is held down, so the pitch sits low or sinks. Owners reported this on the KN7000 and on older models. Source: Community report, 2007–2012

  1. Unplug every footswitch and play again.
  2. If that cures it, press PROGRAM MENUS, choose CONTROL, then FOOT CONTROLLERS, and give FOOT SWITCH 1 and 2 the jobs you want.
  3. Push a jack plug in and out of the socket a few times to clean it.

Source: Community report, 2007–2012

Each part can also ignore the glide: GLIDE PEDAL on page 3 of the sound menu’s PART SETTING turns it on or off for that part. Source: Manual, p. 155

One part plays in the wrong key or out of tune

KEY SHIFT moves a part up or down in semitones, from −24 to +24. TUNING fine-tunes it, from −128 to +127. Both are set per part. Source: Manual, p. 154 Owners found them set by bought files and by panel memories, the keyboard’s stored set-ups: a part a semitone up, or one tuned right down. Source: Community report, 2006–2007

To check, press PROGRAM MENUS, choose SOUND, then PART SETTING. Choose the part with the PART SELECT buttons. KEY SHIFT and TUNING are on page 1. Source: Manual, p. 154 Then check TRANSPOSE and R1/R2 OCTAVE. Source: Community report, 2006–2025

On a KN5000, Right 2 drops an octave when Left comes on

In the one report, the cause was an octave setting for split playing, stored in the sound’s own edit settings. Source: Community report, 2016

Rhythm and style

The rhythm won’t start

Check three things:

  • CLOCK is set to MIDI, so the style waits for timing from another instrument. Set it to INTERNAL: press PROGRAM MENUS, choose MIDI, then REALTIME MESSAGES. It also returns to INTERNAL at every switch-on.
  • The DRUMS volume is at its minimum on the home page. Turn it up with its balance buttons.
  • The sequencer’s PLAY button is on. Turn it off when not playing back a song.

Source: Manual, pp. 191, 201

The style plays at the wrong tempo

With MUSIC STYLE ARRANGER off, choosing a style keeps the tempo already set. Source: Tested on a KN7000 Holding ONE TOUCH PLAY sets the style’s own tempo, with sounds to suit it. Source: Manual, p. 61 See Set the sounds and tempo for a style.

Volumes jump when you change variation

A variation is one of a style’s four versions. With MUSIC STYLE ARRANGER on, changing variation also changes the panel’s settings to suit the style. Source: Manual, p. 64 One owner’s volumes jumped as high as 127 at each change. Source: Community report, 2024

To choose what it changes, hold MUSIC STYLE ARRANGER for a few seconds. RHYTHM changes only the rhythm. PANEL MEMORY recalls panel memories 1 to 4 of bank A, set up beforehand. Source: Manual, pp. 64, 65

A fade-out ends with a loud last chord

FADE OUT’s Auto Reset returns every part to its set volume when the fade ends. To reach it, hold FADE OUT for a few seconds and choose Auto Reset. Source: Manual, p. 59 One KN7000 owner’s last chord came back at full volume with it on. Switching it off cured it. It goes back on at every switch-on, so the owner stored it in a panel memory. Source: Community report, 2006

A full chord plays as G7 after loading a song

The chord mode sets how the keyboard reads the chord the left hand plays for the band. Source: Manual, p. 54 A community report says that loading a song can switch it to one-finger, and that full chords then come out as other chords: C, E and G played as G7. Source: Community report This doesn’t match the manual, which says BASIC, the one-finger mode, reads three or more keys as a full chord. Source: Manual, p. 54 Check the mode after loading a song: press MODE in the AUTO PLAY CHORD section. Source: Manual, p. 55 See Choose how chords are read.

The chord display shows a chord “on” another note

ON BASS is on. In FINGERED or PIANIST mode it makes the bass play the lowest note of the chord as played, so G, C and E give C on G. Source: Manual, p. 55 It’s on the screen that MODE opens. Source: Manual, p. 55 On a KN6000, a style switched it on. Source: Community report, 2015

TECHNI-CHORD keeps changing type

TECHNI-CHORD adds harmony notes to the right-hand melody. One Touch Play and MUSIC STYLIST, which sets up the panel for a style of music, each choose a TECHNI-CHORD type to suit. Source: Manual, pp. 48, 61 So a type chosen by hand changes when either is used. The advice given to one owner was to store the type in a panel memory. Source: Community report, 2008 To choose the type again, hold TECHNI-CHORD for a few seconds. Source: Manual, p. 48

Tempo or transpose won’t stay as set

With the panel memories in EXPAND mode, each one stores the tempo and TRANSPOSE along with the sounds, so recalling one puts back the stored values. Source: Manual, p. 67 To choose what’s stored, hold SET for a few seconds, then go to page 2/2, the EXPAND MODE FILTER. Source: Manual, p. 67 Owners who wanted their own tempo or transpose to stay were told to set TEMPO and TRANSPOSE off there. Source: Community report, 2008–2011 On a KN5000, the same EXPAND filter for TRANSPOSE was the cause. Source: Community report, 2010

A custom style’s pads don’t come back

Custom styles are styles kept in the 20 CUSTOM slots, and each has its own bank of pads. The performance pads are six buttons that play short phrases. Choosing a custom style doesn’t bring back its pads. Source: Tested on a KN7000 Copying its CUSTOM slot to a composer memory does, along with panel memories 1 to 4 of that bank. The composer is the keyboard’s style editor. Source: Manual, p. 121

Keys and pedals

The keys play at one volume however hard you press

Touch response is how much a key’s volume follows how hard it’s played. Press PROGRAM MENUS, choose CONTROL, then OVERALL TOUCH SENSITIVITY. VELOCITY SENSE runs from 0 to 9, and 0 turns touch response off. Source: Manual, p. 179 More on the keys and buttons page.

A volume pedal does nothing after a MIDI file loads

An expression pedal, used as a volume pedal, only sends a change when it moves. A MIDI file’s own volume overrides it until then. Move the pedal and it takes over again. This was reported on a KN2000. Source: Community report, 2007

Display

Save and load no longer ask before going ahead

The confirmation messages have been switched off. Press CUSTOMIZE and choose DISPLAY TIME OUT. Choose ARE YOU SURE? with the DISPLAY TYPE buttons, set it to DEFAULT with the TIME buttons, and press OK. Source: Manual, p. 183 One KN7000 owner found this after the keyboard stopped asking before saving, loading and overwriting. Source: Community report, 2008

Card and disk

MIDI files don’t show in the list

The load screen lists either the keyboard’s own files or MIDI files. On the floppy’s load screen, press SMF to list MIDI files and TECH to go back. Source: Manual, pp. 125, 126 On the card’s load screen, SD-SOUND on page 1/3 lists them. Source: Manual, p. 142 That was the answer given when owners couldn’t find MIDI files on a disk. Source: 2 community reports, 2013–2014

Files copied to a card from a computer are a different problem: see Files from a computer don’t show on the card.

The keyboard goes silent while loading or saving

That’s normal. No sound comes out during card operations such as LOAD and SAVE, or while some card screens are open, such as page 3 of the load screen and SD SONG MEDLEY. Source: Manual, p. 139 Load between songs, not during one.

The floppy light stays on, the drive is noisy, or the case is warm

All three are normal. The KN7000’s floppy drive light stays on all the time. Source: 2 community reports, 2016 The drive makes a noise while it reads. Source: Manual, p. 202 The case gets warm because the power supply is built in. Source: Manual, p. 202 On the KN7000 it’s the left side, where the supply sits. Source: Community report, 2008

MIDI

No MIDI reaches the KN7000, and the MIDI menu says “Attention”

The MIDI IN / BASS PEDAL switch on the back is set to BASS PEDAL, for a MIDI pedal unit. The keyboard’s MIDI input settings then don’t work. Switch off, set the switch to MIDI IN, and switch on again. Source: Manual, p. 199 Owners reported an “Attention” message on opening the MIDI menu with the switch set this way. Source: 2 community reports, 2010–2026

No MIDI out of a KN5000 or KN6000

The computer switch on the back of these models turns MIDI OUT off when it’s set to PC or MAC. Set it to MIDI with the power off. Source: 2 community reports, 2008–2011

Over MIDI, the band plays only drums after old files are loaded

A loaded file can change the parts’ MIDI channels. At a KN7000, loading old floppies set every part’s channel to OFF. Over MIDI the band then played only drums, and intros, fills and endings did nothing. Source: Tested on a KN7000

The cause was From Registration file, under MIDI SETTING LOAD OPTION, set to YES, so loading took the file’s MIDI settings too. The manual’s screen picture shows NO as the factory setting. Source: Manual, p. 185 To reach it, press CUSTOMIZE and choose MIDI SETTING LOAD OPTION. Source: Manual, pp. 181, 185

A MIDI set-up stored as a user setting under MIDI PRESETS puts the channels back: press PROGRAM MENUS, choose MIDI, then MIDI PRESETS, and recall it on page 3/4. Source: Tested on a KN7000

Right 1’s sound changes by itself with MIDI connected

PROGRAM CHANGE TO P. MEM is on. It ties program changes, the MIDI messages that choose sounds, to the panel memories, so incoming ones recall panel memories. It also takes over Right 1’s sound changes. Source: Manual, p. 192 Source: Tested on a KN7000 If it isn’t needed, turn it off: press PROGRAM MENUS, choose MIDI, then COMMON SETTING. Source: Manual, p. 192

The rhythm starts when the computer plays

REALTIME COMMANDS is receiving start and stop messages from the computer. To stop it, press PROGRAM MENUS, choose MIDI, then REALTIME MESSAGES, and set REALTIME COMMANDS to OFF. Source: Manual, p. 191 Source: Community report, 2011

When to call a repairer

Most items above are settings or normal behaviour, and need no repairer. A footswitch socket that stays faulty after cleaning is a repairer’s job. Source: Community report, 2007–2012 When the settings are right and the problem stays, go on to the page for the symptom: No sound, or some parts silent, Keys and buttons or Computer, USB and MIDI.

Corrections and owners' experience: hello@knarrangers.com

All troubleshooting pages · FAQ

Last checked 15 Nov 2026