Troubleshooting · KN7000Settings lost after switching off
What the KN7000 keeps when it's switched off, what owners report losing, and the checks in order.
About 30 owners reported on forums that their settings had gone after switching off. Source: 30 community reports, 2006–2019 The answer given most often, and confirmed many times, was that the settings had never been saved to a card or floppy. Source: Community report, 2006–2019
What the KN7000 keeps when it’s switched off
The keyboard holds its memory for a while without power. The manual gives these times:
- About a week: the panel’s current settings, the panel memories (stored set-ups of the panel), the sound memory (edited sounds) and the effect memory.
- About 80 minutes: the sequencer’s songs, the composer memories and the user banks of the performance pads. The sequencer is the built-in recorder, the composer is the style editor, and the pads are six buttons that play short phrases.
- With no limit: the MIDI set-ups stored under MIDI PRESETS (MIDI is the link to computers and other instruments), the favourites, the home-page layout and all the custom styles in CUSTOM 1–20.
The backup only protects a change once the keyboard has been on for about 10 minutes. Source: Manual, p. 198
What owners report
Some owners’ reports don’t fit those times. They lost settings within minutes, within a few hours, or overnight. Source: Community report, 2006–2018 Owners suspected a worn backup part, described below. Source: Community report, 2006–2018
A check at a KN7000 is planned: store changes after the keyboard has been on for more than 10 minutes, then note what survives two hours switched off, and then two days. Until then, save before switching off rather than relying on the times above.
The checks
- Save everything you want to keep to a card or floppy before switching off: Save your work to a card or floppy. In the save options, PERFORM selects all the performance data, the first two groups above, and BACKUP all the backup data, the third. Source: Manual, pp. 148, 198 On floppy, backup data needs a 2HD disk. Source: Manual, p. 122
- After changing anything you want kept, leave the keyboard on for at least 10 minutes before switching off. Source: Manual, p. 198
- Check whether the setting is one that goes back at every switch-on:
- MONITOR SETTING: the speakers come back on. Source: Manual, p. 160
- CLOCK returns to INTERNAL. Source: Manual, p. 191
- FADE OUT’s Auto Reset, which returns the parts to their set volume after a fade-out, goes back on. One owner stored the setting in a panel memory. Source: Community report, 2006
- If footswitch and pedal jobs are forgotten: they’re set under PROGRAM MENUS, CONTROL, FOOT CONTROLLERS. Source: Manual, p. 179 For the KN7000, the advice given was to set them there and save to the card. Source: Community report, 2022
Lost after loading a file
Loading replaces what’s in the memories it loads into. Source: Manual, p. 202 One save on a card or floppy holds up to 11 kinds of data, and loading the whole save overwrites them all. Source: Manual, pp. 122, 141, 148, 198 A one-song sequencer file from an older model goes into song 1 and erases songs 2 to 10. Source: Manual, pp. 125, 140
Before loading, save your own work. Then choose what to load: on page 2/3 of the load screen, set each kind of data to YES or NO. Source: Manual, pp. 125, 141 See Load a save from a card or floppy.
What owners lost this way, and what kept it:
- The pads. A save that holds everything brings its own pads. Owners saved their pads on their own, with only PERFORMANCE PADS set to YES, and loaded them back afterwards. Source: 2 community reports, 2008–2023
- The panel memories. To keep your own, set PANEL MEMORY to NO in the load options, and load panel memories on their own when you want them. Source: Manual, pp. 125, 141 DATA PROTECTION, on the CUSTOMIZE menu, doesn’t cover them: it protects other settings from a load, such as the footswitch jobs, the touch settings and the mic setting. Source: Manual, p. 184
- The custom styles, missing from a song’s save. A save holds them only when ALL CUSTOM STYLE is set to YES, or when BACKUP is pressed. Source: Community report, 2007 Source: Manual, p. 148
- The MIDI set-up. Files carry MIDI settings. MIDI SETTING LOAD OPTION, on the CUSTOMIZE menu, sets whether loading panel data or a sequencer song also loads them. For songs that switch on the GM2 or NX SOUND mode, KEEP leaves them unchanged. Source: Manual, p. 185 Store your set-up as one of the three user settings under MIDI PRESETS, where it’s kept with no time limit, and save it to the card. Source: Manual, pp. 194, 195, 198 At a KN7000, loading old floppies set every part’s MIDI channel to OFF; recalling the stored user setting put it back. Source: Tested on a KN7000
- The edited sounds. Loading a file that holds sounds replaces the sound memory. Source: Community report, 2021
- Edited effects, lost with a song. The advice given was to save with the EFFECT option set to YES, and to keep effect edits in an effect memory, the store for edited effect settings. Source: 2 community reports, 2006–2007
- Sound Arranger changes, after INITIAL (the menu reset) or a power cut. Sound Arranger chooses other sounds for a style’s accompaniment parts. Source: Manual, p. 60 One owner was told they can’t be saved on their own, and to copy the style to the composer to keep them. Whether a panel-memory save keeps them is disputed. Source: Community report, 2006
The backup part
Owners report that the memory is held up by a capacitor inside, not a battery, and that a worn one shortens the times above. Source: Community report, 2006–2018 Their reports of which part it is come from older KN models. For the KN7000 it isn’t settled. Source: Community report, 2008–2017
A test given in one 2009 report: if the panel memories, the edited sounds and the composer data are all gone after a short time switched off, suspect the backup part. If only changes made while playing go, the cause is elsewhere. Source: Community report, 2009
One owner whose keyboard had been in long storage was advised to leave it switched on for some hours before judging the backup part. Source: Community report, 2018
On older KN models, owners report that replacing the capacitor cured the fault. It means opening the keyboard and soldering: a repairer’s job. Source: 4 community reports, 2011–2017
When to call a repairer
When settings go within minutes or overnight, after the keyboard had been on for more than 10 minutes, and the test above points to the backup part.
Related
- Save your work to a card or floppy
- Load a save from a card or floppy
- Store your set-up in a panel memory
- Settings that look like faults
- When and how to reset
Corrections and owners' experience: hello@knarrangers.com
All troubleshooting pages · FAQ
Last checked 15 Nov 2026