Troubleshooting · KN7000When and how to reset

The steps in order when the keyboard behaves oddly, from switching off and on to the menu reset and, last, the power-on reset that erases the memory.

Written for: KN7000.Also called: reset, factory reset, master reset, hard reset, power-on reset, initialise, initialize, INITIAL, Factory Initial, all initial, keyboard acting strangely, buttons not working, keys not working, restore factory settings, Initial Data Disk, reboot, restart.

A reset puts settings and memories back to how they left the factory, and erases what they held. Source: Manual, p. 197 Work through the steps below in order, and stop at the first one that cures the fault.

Many faults that seem to need a reset turn out to be a setting. Check Settings that look like faults first. Source: Community report, 2004–2026

1. Switch off and on

Switch off with POWER, wait a few seconds, and switch on again. The manual gives this as the first remedy when buttons or keys misbehave. Source: Manual, p. 201

Switching on also puts two settings back: the speakers come back on if MONITOR SETTING was off, and CLOCK returns to INTERNAL. Source: Manual, pp. 160, 191

2. Save everything

Every reset below erases something, so save first: Save your work to a card or floppy. In the save options, PERFORM selects all the performance data: the panel’s settings and its stored set-ups (panel memories), the songs in the sequencer (the built-in recorder), the composer memories (the style editor’s), the edited sounds and effects, and the user banks of the performance pads (six buttons that play short phrases). BACKUP selects all the backup data: the custom styles in CUSTOM 1–20, the MIDI set-ups stored under MIDI PRESETS (MIDI is the link to computers and other instruments), the favourites and the home-page layout. On floppy, backup data needs a 2HD disk. Source: Manual, pp. 122, 148, 198

3. The menu reset, INITIAL

INITIAL, on the CONTROL menu, resets one section of the memory at a time, or all the performance data at once. Source: Manual, p. 197 It leaves alone the MIDI set-ups stored under MIDI PRESETS, the favourites, the home page and the custom styles. Source: Manual, p. 197 The steps are in Return settings to factory.

Reset only the section that seems to be at fault first: MIDI SETTING when MIDI misbehaves, or CURRENT PANEL for the panel’s settings. PERFORMANCE resets every section on the list at once. Source: Manual, p. 197 On a second-hand KN7000 with every part’s MIDI channel set to OFF, resetting MIDI SETTING put back the MIDI settings and nothing else. Source: Tested on a KN7000

To tell a data fault from a hardware one: after INITIAL, load only the style you were using. If the fault has gone, it was in the data. Source: Inferred

The sources disagree on one point. A 2006 forum post says initialising also wipes the stored MIDI set-ups. Source: Community report, 2006 The manual says INITIAL doesn’t. Source: Manual, p. 197 The post may refer to the power-on reset below. Source: Inferred Save the MIDI set-up to a card either way.

INITIAL doesn’t reset the custom styles. The manual’s way to put them back to factory is to load the Initial Data Disk, a floppy that came with the keyboard. It replaces the styles in CUSTOM 1–20, so save them first. Source: Manual, p. 121 A community report says that loading its files also resets the MIDI settings, the favourites and the home page. Source: Community report, 2015–2016

4. The power-on reset, last

Use it only when the steps above haven’t helped.

The manual gives one power-on reset for the KN7000. Switch off, then hold 60s & 70s, MODERN DANCE and SOUL & R&B, the three lower-left buttons of the RHYTHM GROUP section, while switching on again. Source: Manual, pp. 197, 201 The steps, with a drawing of the buttons, are under The full reset in Return settings to factory.

The manual’s two pages differ on what it erases. One says all the performance data. Source: Manual, p. 197 The other says every setting, function and memory goes back to factory. Source: Manual, p. 201 Treat it as erasing everything, the custom styles and the stored MIDI set-ups included. Source: Inferred

Loading the save afterwards puts its data back in the keyboard. Source: Manual, p. 202

Owners also report a second hold that isn’t in the manual: 8 & 16 BEAT, ROCK & POP, BALLAD and JAZZ & SWING, the four upper-left RHYTHM GROUP buttons. They report the screen then showing “Factory Initial Completed”. Owners’ names for the two holds disagree, and what each one keeps isn’t settled. Source: 5 community reports, 2006–2019 The manual gives only the lower-left hold. Source: Manual, pp. 197, 201

Other button holds at switch-on start the keyboard’s service tests. Don’t hold buttons while switching on except as the manual says. Source: Service manual, pp. 27–28

When to call a repairer

When the fault stays after switching off and on, the menu reset and the data check above. On one KN7000 with keys dead in a pattern, a factory reset didn’t help. Source: Community report, 2019 Buttons that need a hard press, and keys that play too loud or too quiet, have their own checks: see Keys and buttons.

Corrections and owners' experience: hello@knarrangers.com

All troubleshooting pages · FAQ

Last checked 15 Nov 2026