Troubleshooting · KN7000Buttons that need a hard press, or keys too loud or too quiet

Checks in order when panel buttons stop answering, or single keys play too loud, too quiet or only when struck hard.

Written for: KN7000.Also called: button not working, buttons stiff, hard press, button needs pressing hard, START/STOP not working, FILL IN not working, panel memory button dead, key too loud, key too quiet, dead key, silent key, key needs hitting hard, velocity, touch response, touch sensitivity, VELOCITY SENSE, aftertouch, keys dead in a pattern, rubber contacts.

Check the settings and the data before the hardware.

The settings

  1. Switch off with POWER, wait a few seconds, and switch on again. Source: Manual, p. 201
  2. Check the touch response, which is how much a key’s volume follows how hard it’s played. Press PROGRAM MENUS, choose CONTROL, then OVERALL TOUCH SENSITIVITY. VELOCITY SENSE runs from 0 to 9. At 0, touch response is off and every key plays at the same volume. Source: Manual, p. 179
  3. Check the aftertouch, which adds an effect when a key is pressed harder after it’s down. It’s switched on or off for the whole keyboard on the same screen, where THRESHOLD sets how hard the press must be. Source: Manual, p. 179 Each part also has its own AFTER TOUCH switch, on page 3 of the sound menu’s PART SETTING. Source: Manual, p. 155
  4. The sequencer, the keyboard’s built-in recorder, records aftertouch only when AFTER TOUCH SETTING is on. It’s off from the factory. Source: Manual, p. 100

The manual’s next remedy, after switching off and on, is a reset that erases the memory. Read When and how to reset before trying one. Source: Manual, p. 201

The data

To tell a data fault from a hardware one: save your work, reset the performance data (the panel and its memories) with INITIAL, the menu reset, then load only the style you were using. If the key or button behaves, the fault was in the data. Source: Inferred Both steps are in Save your work to a card or floppy and Return settings to factory.

Buttons that need a hard press, or don’t answer

Owners reported this on the KN7000 and on other KN models. On the KN7000 it was START/STOP, FILL IN 1 and INTRO & ENDING 1, and the panel-memory buttons, which recall stored set-ups. Source: 8 community reports, 2006–2018

  1. Blow the dust out from around the buttons with dry compressed air. Source: Community report, 2013 Don’t use contact spray: owners report it making faults worse. Source: Community report, 2006–2025
  2. Give the same job to a footswitch, a pedal that plugs into FOOT SW 1 or FOOT SW 2 on the back. START/STOP, both FILL IN buttons and both INTRO & ENDING buttons can each be put on one. Press PROGRAM MENUS, choose CONTROL, then FOOT CONTROLLERS. Source: Manual, pp. 179, 180, 199
  3. If the footswitch works and the button doesn’t, the fault is in the button. One owner with a faulty START/STOP gave its job to a footswitch instead. Source: Community report, 2012

The causes owners and repairers found were worn switches under the buttons, and once a cracked board under START/STOP. The fix is a new switch or board, which means opening the panel and soldering: a repairer’s job. Source: Community report, 2006–2012

Keys too loud, too quiet, or silent until struck hard

Each key presses a rubber contact on a board underneath. Owners trace a key that plays loud, quiet or only when struck hard to dirt or wear on its contact. Source: Community report, 2008–2026 Two owners fixed it by fitting a contact strip from another octave or from another keyboard. Source: 2 community reports, 2014–2017 Cleaning the contacts was also suggested, with no result reported. Source: Community report, 2009–2026

On the KN7000, two owners reported the lowest B silent or quiet until struck hard. One suggested cause, not confirmed, is the rail at the back that the keys sit in. Source: 2 community reports, 2013

Both mean opening the keyboard: a repairer’s job. Source: Community report, 2013–2017

Several keys dead or loud in a pattern

When the faulty keys repeat across the octaves, for example every D, F♯ and B♭, owners and repairers found the fault in the keyboard’s wiring or its circuit board, not in the contacts. This is a repairer’s job. Source: 9 community reports, 2009–2025 On one KN7000 with that pattern, a factory reset didn’t help. Source: Community report, 2019

When to call a repairer

When the settings and the data check don’t help, when a footswitch works but the button doesn’t, and when keys fail in a pattern. Each fix means opening the keyboard.

Corrections and owners' experience: hello@knarrangers.com

All troubleshooting pages · FAQ

Last checked 15 Nov 2026