Troubleshooting · KN7000, KN6000, KN5000USB or MIDI doesn't work with a computer
Checks in order when a computer or another instrument gets nothing from the KN7000, or the KN7000 ignores what is sent to it, over USB or the MIDI sockets.
MIDI is the standard way keyboards, computers and other instruments send notes and settings to each other. Source: Manual, pp. 187–188 The KN7000 has two ways to a computer: its USB socket, and its MIDI sockets through a USB-MIDI interface, a cable or small box with MIDI plugs at one end and USB at the other. They carry different things.
- Over USB, the computer gets the keyboard’s sound, its tempo, start and stop, and button changes. The keyboard obeys notes and settings the computer sends.
- Notes played on the keys, the left-hand chord and the band’s notes (the accompaniment) don’t arrive over USB. The MIDI sockets carry them.
The KN7000 page sets out what each connection carries.
The settings
The MIDI settings are on the MIDI menu: press PROGRAM MENUS and choose MIDI. Source: Manual, p. 189
- Check the MIDI IN / BASS PEDAL switch on the back. On BASS PEDAL it serves MIDI bass pedals, and every MIDI setting except MIDI OUT stops working. Switch off, set it to MIDI IN, and switch on again. Source: Manual, pp. 187, 199 Owners with the switch on BASS PEDAL saw an Attention message when they opened the MIDI menu. Source: 2 community reports, 2010–2026
- Check the channels on PART SETTING. Each part, from the sounds played on the keys to each part of the band, sends and receives on its own MIDI channel. A part set to OFF neither sends nor receives. From the factory, Right 1 is on channel 1, Right 2 on 2, Left on 3, and parts 4 to 16 on their own numbers. The accompaniment, bass, drums, chord and control parts are off until given a channel. Source: Manual, p. 190 The sending and receiving sides must use the same channels. Source: Manual, pp. 188, 202
- For the band’s notes to go out, turn on AUTO PLAY CHORD OUTPUT and DRUM PATTERN OUTPUT, on INPUT/OUTPUT SETTING, as well as giving the parts channels. Source: Manual, pp. 193–194 Owners report the drum output off from the factory. Source: Community report
- Check LOCAL on PART SETTING. Set to OFF, a part’s notes go out over MIDI but the keyboard doesn’t sound them. Source: Manual, p. 190 If notes sound doubled or thin with a computer connected, the computer’s software may be sending back what it receives. Set the software not to send it back, or set LOCAL to OFF. Source: Manual, p. 202
- Check NOTE ONLY, on COMMON SETTING. When it’s on, only notes pass: sound changes, pedals and pitch bend don’t. Source: Manual, p. 192 It stopped pitch bend reaching one owner’s KN6000. Source: Community report, 2006
- If the style, the accompaniment pattern, won’t start, check CLOCK, on REALTIME MESSAGES. On MIDI, the style waits for a tempo clock from outside. Set it to INTERNAL. It goes back to INTERNAL each time the keyboard is switched on. Source: Manual, pp. 191, 201 A style also won’t start with the drums’ volume at its minimum, or with PLAY in the SEQUENCER section on. Source: Manual, p. 201
- If the style starts by itself when the computer starts a song, REALTIME COMMANDS, on the same page, is passing start and stop across. Set it to OFF. Source: Manual, p. 191 Source: Community report, 2011
MIDI PRESETS sets the channels for common set-ups in one go. Page 1/4 lists set-ups where the KN7000 receives, such as EXTERNAL SEQUENCER, and page 2/4 set-ups where it sends. WITH APC includes the band and WITHOUT APC leaves it out. Source: Manual, p. 194 Choosing one replaces the current MIDI settings, so store a working set-up first (below). Source: Inferred
Error 62
Error 62 says the computer connection isn’t active because the computer-port switch is set to MIDI, and asks for the power to be off while the switch is changed. Source: Manual, p. 204 The KN7000’s back panel, as the manual describes it, has no computer-port switch. Source: Manual, pp. 199–200
The KN5000 and KN6000 have a MIDI / PC switch on the back. Set to PC or MAC, it stops MIDI OUT. Change it with the power off. Source: 2 community reports, 2008–2011
The data
- Loading old floppies can set every part’s channel to OFF. Over MIDI the band then played drums only, and intros, fills and endings did nothing. This happens when MIDI SETTING LOAD OPTION, on the CUSTOMIZE menu, is set to load MIDI settings with the file. Source: Tested on a KN7000 The factory setting shown in the manual is NO. Source: Manual, p. 185
- A second-hand keyboard may keep its last owner’s MIDI settings. One had every part’s channel off. Source: Tested on a KN7000 MIDI SETTING, on the INITIAL screen, resets the MIDI settings and nothing else: see Return settings to factory. Source: Manual, p. 197
- Page 4/4 of MIDI PRESETS stores a working set-up as one of three user settings, and page 3/4 recalls it. User settings stay in the keyboard with the power off. Source: Manual, pp. 195, 198 Recalling one put the channels back after a load had switched them off. Source: Tested on a KN7000
Cables, USB and drivers
- MIDI OUT goes to the other device’s MIDI IN, and the other device’s MIDI OUT to the KN7000’s MIDI IN. Source: Manual, p. 187 Owners found the plugs the wrong way round, or a low-cost USB-MIDI cable with its IN and OUT swapped. If nothing arrives, swap them. Source: 3 community reports, 2006–2015
- Stuck or missing notes through a low-cost USB-MIDI cable: owners cured them with a better-made interface. Source: 3 community reports, 2017–2021 For several instruments chained one after another, a multi-port interface was suggested. Source: Community report, 2018 One report blames a busy style sending more than a MIDI cable carries. Source: Community report, 2025
- On a Mac, notes played on the keys don’t arrive over USB. Source: Tested on a KN7000 Owners on later Windows versions, macOS and iPad report the same, and blame the computer’s general USB MIDI driver: in 2008 one owner on Windows XP played a computer from the keys over USB. Source: 5 community reports, 2008–2023 Use the MIDI sockets for what’s played, and USB for the sound and for what the computer sends. Leave COMPUTER CONNECTION, on the MIDI menu, on NORMAL. Source: Tested on a KN7000
- The sound sent over USB is taken before MAIN VOLUME, so the slider doesn’t change the recording level. It includes LINE IN but not AUX IN. Source: Manual, p. 200
- The USB socket connects to a computer. Source: Manual, p. 199 It doesn’t read USB sticks or drives. Source: Community report, 2005
Drivers
- On a Mac, no driver is needed. The KN7000 appears as a stereo audio device and two MIDI ports, about two minutes after switching on. Source: Tested on a KN7000
- One owner recorded the keyboard straight into an iPad over USB, with no driver. Source: Community report, 2022
- On Windows, the manual says to install the USB driver from the CD that came with the keyboard first. Then connect the keyboard while it’s switched off, and switch it on. Source: Manual, p. 196
- Windows often installs only one of the keyboard’s two USB devices, the MIDI one or the audio one. Owners fixed this with the install guide on the keyboard’s CD, or in Windows’ list of devices: they updated the USB audio device’s driver by hand, chose the keyboard’s own entry, and restarted with the keyboard on. Source: 2 community reports, 2007–2008
- Owners report no driver for 64-bit Windows. They use a Windows XP virtual machine, or the MIDI sockets. Source: 2 community reports, 2008–2017
- The recording program on the keyboard’s CD recorded silence for one owner. Another recording program, set to the keyboard’s USB audio device, worked. Source: Community report, 2008
The hardware
One KN7000’s dead MIDI OUT came back after work on its power supply. Source: Community report, 2017
When to call a repairer
When the settings above are right, the cables are the right way round, an interface that works with another instrument has been tried, and a socket still sends or receives nothing. Work on the sockets or the power supply needs the case opened. Source: Inferred
Related
- Switch on, set the volumes and play
- Return settings to factory
- Load a save from a card or floppy
- Connecting a computer, on the KN7000 page
- Settings that look like faults
Corrections and owners' experience: hello@knarrangers.com
All troubleshooting pages · FAQ
Last checked 15 Nov 2026