Technics KN7000 · Disk and SD cardLoad files from an older Technics keyboard
What loads
The KN7000 Reference Guide names seven older models whose data the KN7000 plays: the KN6000 and KN6500, the KN5000, KN3000 and KN2000, and the KN1600 and KN1400. Source: Reference Guide, p. 54
From those models, recordings made on the sequencer (the keyboard’s built-in recorder) carry over. So do styles made in the composer (its style editor), panel settings and panel memories (stored set-ups), edited sounds in the sound memory, and the performance pads’ user banks. The pads are the six buttons that play short phrases. Source: Reference Guide, p. 54
- The manuals say custom styles don’t load. The Reference Guide says this of the KN5000’s and the KN6000’s and KN6500’s custom styles. The owner’s manual says it of custom styles from any older model. Source: Reference Guide, p. 54 Source: Manual, pp. 125, 140
- Two KN6000 custom-style sets have loaded on a KN7000 all the same. Source: Tested on a KN7000
- Effect memories aren’t on the Reference Guide’s list. Source: Reference Guide, p. 54
- Data from older models may load as performance data only. That’s the panel, panel memories, sequencer, composer, sound memory, pads and effect memory, not the backup data. Source: Manual, pp. 122, 198
The KN7000 page lists which other models’ files load, and which don’t.
Tried on a KN7000
- A KN6000 song set loaded and was saved again in the KN7000’s own form. Source: Tested on a KN7000
- A KN5000 sound bank loaded and was saved again as a KN7000 bank. No KN5000 style has been tried yet. Source: Tested on a KN7000
- Four styles on KN3000-format floppies were tried. Three loaded and were saved again; the fourth was refused, cause unknown. Three KN3000 sound banks loaded. Source: Tested on a KN7000
Before loading
- Loading replaces what is in the memories it loads into. To keep them, save first: see Save your work to a card or floppy. Source: Manual, pp. 125, 140, 202
- When the keyboard is used with MIDI, store its MIDI set-up as a user setting first: see Keeping your own MIDI set-up. Loading old floppies has switched every MIDI channel off: see After loading. Source: Tested on a KN7000
Loading an old save
An old save loads like any other: see Load a save from a card or floppy.
- Put the floppy in the drive, or the card in the SD slot.
- Hold DISK or SD for a few seconds. The load screen opens.
- Choose the save and press LOAD. The screen shows COMPLETED! when the load has finished.
- Some older models’ sequencer saves hold only one recording. One of these loads into song 1 and erases songs 2 to 10. Source: Manual, pp. 125, 140
- Error 43 means the file was saved on an older KN keyboard and loads only with the PERFORMANCE option. Source: Manual, p. 203 The manual doesn’t say where that option is set. On the LOAD OPTION page, setting the four backup kinds (USER MIDI SETTINGS, FAVORITES, HOME PAGE and ALL CUSTOM STYLE) to NO may be what it means. Source: Inferred
- MIDI files saved on an older Technics model in its own Technics mode load through the MIDI-file load screen. Choose PREV. TEC → NX as the LOAD AS setting. The volume balance and octaves may differ from the original. Source: Manual, p. 126
What changes
The Reference Guide warns of these differences with data from older models. Source: Reference Guide, p. 54
Sounds and effects
- Sounds may come out a little different, as the KN7000’s sound generator and effects differ from older models’. Source: Reference Guide, p. 54
- An edited sound built on a waveform, the basic recorded tone, that the KN7000 doesn’t have sounds different. Source: Reference Guide, p. 54
- The KN7000 can play a different number of notes at once, which can change how a piece sounds. Source: Reference Guide, p. 54
- Reverb and multi effects keep only their effect type, as the KN7000’s effects are built differently. Source: Reference Guide, p. 54
- If a loaded recording or style plays other sounds than the ones chosen, choose the sounds again. Source: Manual, p. 201
Styles and pads
- Built-in styles and pad phrases in the old data change to the KN7000’s own. Source: Reference Guide, p. 54
- Composer fills, intros and endings recorded with the older composer’s mode set to NORMAL don’t play. Source: Reference Guide, p. 54
- From the KN2000, some intros and fills made in the composer’s Expand mode may play differently. Source: Reference Guide, p. 54
Recordings
- Old recordings may play in the wrong octave. The KN7000 plays every sound in a recording at the same octave setting, where older models could set the octave sound by sound. Source: Reference Guide, p. 54
- Harmony notes added by Techni-Chord, the automatic harmony, aren’t played back. Source: Reference Guide, p. 54
- Features the KN7000 doesn’t have don’t carry over. Composer, sequencer or panel data that uses them may not play correctly. Source: Reference Guide, p. 54
Loading one item from an old save
Single load puts one bank or one item from a save into a chosen place in the keyboard, such as one panel memory or one sound. It doesn’t work on data from older models. Source: Reference Guide, p. 54
The German text of the Reference Guide gives the way round: load the whole save into the KN7000, save it again, then single-load from the new save. The English text gives only the limit. Source: Reference Guide, p. 55
- Save what is in the keyboard now.
- Load the whole old save.
- Save it again on the KN7000, in a new place on the card or floppy. See Save your work to a card or floppy.
- Load the save from step 1 back in.
- Choose the new save on the load screen, press PAGE to go to page 3, SINGLE LOAD, and load the item. See Load a save from a card or floppy.
Source: Reference Guide, p. 55
Steps 1 and 4 keep what was in the keyboard, since loading replaces the memories it loads into. Source: Manual, pp. 125, 140
After loading
- Loading old floppies has set every part’s MIDI channel to OFF. This happens when MIDI SETTING LOAD OPTION, on the CUSTOMIZE menu, is set to load MIDI settings with the file. Recalling a stored MIDI user setting put the channels back. Source: Tested on a KN7000 The manual’s picture of that screen shows From Registration file set to NO, but doesn’t say this is the factory setting. Source: Manual, p. 185
- The other checks after any load, such as the chord mode, are in Load a save from a card or floppy.
Manual pages
KN7000 Reference Guide, pp. 54–55.
Corrections: hello@knarrangers.com
Guide D6 · last checked 18 Nov 2026